11/13/2022 0 Comments Fmc micromate![]() Fmc micromate manual#0.6 (8/15) MN06150 Ħ Section I Introduction Introduction This manual is to be used for the installation of the Smith Meter Electronic Preset Controller with firmware. Sample Application Power Wiring.43 Issue/Rev. Sample Application DC & Signal Wiring.42 Figure 29. Sample Application AC Wiring.41 Figure 28. Sample Application Worksheet.40 Figure 27. MACF Board / Instrument Power Wiring.38 Figure 26. Promass Coriolis Meter Communications.34 Figure 22. Lubrizol EIA-485 Additive Injector Communications.33 Figure 21. Additive Injector Communications.32 Figure 20. Fmc micromate serial#Multiple Serial Communications.28 Figure 16. General Wiring for Serial Communications.27 Figure 15. Analog Inputs Resistance (RTD) / 4-20ma.26 Figure 14. Wiring Diagram, Typical Metered Injector.25 Figure 13. Wiring Diagram, Open Collector Output.24 Figure 12. Wiring Diagram, Universal Pulse Transmitter (UPT).23 Figure 11. Wiring Diagram, Promass Coriolis Meter.22 Figure 10. Wiring Diagram, PA-6 Transmitters.20 Figure 9. Wiring Diagram, PPS Transmitters.19 Figure 8. Wiring Diagram, PEX-P Transmitter Single Pulse.18 Figure 7. Typical Wire Sizes.8 Maximum Cable Length and Baud Rate (EIA-232).8 Maximum Cable Length and Baud Rate (EIA-485).8 Wiring Checklist.10 MNET Board Terminal Assignments.15 I/O Configuration Worksheet.16 Promass Modeling for Single Pulse Wiring.21 Promass Modeling for Dual Pulse Wiring.21 Wiring Termination for T-568B and T-568A.32 Figures Figure 1. 0.6 (8/15)ĥ Tables and Figures Tables Table 1. 6 Section II Pre-Installation Considerations.7 Mechanical.8 Electrical.8 Section III Installation.10 Mechanical.10 Electrical.10 Start-Up.11 Section IV Diagrams.12 Pulse Inputs.16 Wiring Diagrams.17 Analog Inputs.26 Communications.27 Promass Coriolis Meter Communications.34 Digital Inputs.35 Digital Outputs.36 Instrument Power Wiring.38 Sample Application Wiring.39 Interposing Relays.39 Section V Appendix A ATEX Installation.44 Section VI Related Publications.45 MN06150 Issue/Rev. 0.6 (8/15) MN06150 Ĥ Table of Contents Section I Introduction. Warning On initial power-up of a new unit or after installation of a new computer board, there are several alarms that will be triggered, which cannot be cleared until the is programmed. Failure to provide backup equipment could result in personal injury, property loss and equipment damage. Warning These preset devices must be used with fail-safe backup equipment to prevent accidental runaway delivery of product. Operation of this equipment in a residential area is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. It has not been tested to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Caution This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this Instruction Manual, may cause interference to radio communications. If damage has occurred during shipment or parts are missing, a written report should be submitted to the Customer Service Department, FMC Technologies Measurement Solutions, Inc., 1602 Wagner Avenue, Erie, Pennsylvania Prior to installation, the unit should be stored in its original packing case and protected from adverse weather conditions and abuse. Carefully remove the unit from its packing case and inspect for damaged or missing parts. If the packing case has been damaged, the local carrier should be notified at once regarding his liability. 0.6 (8/15)ģ Receipt of Equipment When the equipment is received the outside packing case should be checked immediately for any shipping damage. hereby disclaims any and all responsibility for damages, including but not limited to consequential damages, arising out of or related to the inputting of incorrect or improper program or default values entered in connection with the. Disclaimer FMC Technologies Measurement Solutions, Inc. Each metering system is unique and each program parameter must be reviewed and programmed for that specific metering system application. 1 Electronic Preset Delivery System Smith Meter Installation Manual Bulletin MN06150 Issue/Rev 0.6 (8/15)Ģ Caution The default or operating values used in this manual and in the program of the Smith Meter are for factory testing only and should not be construed as default or operating values for your metering system. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |